Glysantin® G05®
Cummins CES 14603
Ford North America WSS-M 97B51-A1
JCB STD00088
John Deere JDM H24
MAN B&W Liste 3.3.7
Mercedes-Benz Spezifikation 325.0
MTU MTL 5048
Mercedes-Benz DBL 7700.20, page 325.0
· John Deere JDM H 24
· MTU MTL 5048
· Leyland BLS.22.AF.01
· Ford North America WSS-M97B51-A1
· Chrysler MS – 9769
Glysantin G 05 should possibly not be mixed with silicate free, OAT
engine coolants.
Glysantin G 05 must be diluted with water before use. It is hard water
compatible and can be mixed with tap water* before filling into the
cooling system to give solutions in the concentration range of 33 to
50 % by volume.
* For preparation of the coolant use clean, not overly hard water. Waste
water from mining, sea water, brackish water, brine, industrial waste water
are all unsuitable.
The analysis of the water should not exceed the following limits:
Water hardness 0 to 20 °dGH (0 – 3.6 mmol/l)
Chloride content max. 100 ppm
Sulphate content max. 100 ppm
Should the analysis of the water exceed the approved limits, then it has to
be suitably treated, for example by mixing with pure, distilled or deionised
water. Excessive chloride or sulphate levels can be corrected in this way.
Performance Chemicals
Glysantin G 05
Chemical nature Ethylene glycol with inhibitors
Appearance Clear liquid
Technical data Density at 20 °C 1.131 – 1.133 g/cm³ DIN 51 757/4
Refractive index at 20 °C 1.435 – 1.438 DIN 51 423/2
Boiling point > 160 °C ASTM D 1120
Flash point > 120 °C DIN ISO 2592
pH-value 6.0 – 7.0 ASTM D 1287
Reserve alkalinity, M/10 HCl 15 – 19 ml ASTM D 1287
Ash content max. 2.0 % ASTM D 1119
Water content max. 3.0% DIN 51 777/1
Solubility Miscibility with water freely miscible
Hard water stability stable, no precipitation
Technical data of Freezing point ASTM D 1177
Glysantin G 05 – 50 % vol. in water below – 37 °C
Water mixtures
pH-value ASTM D 1287
33.3 % vol. in water 7.5 – 8.5
2
Frost Protection of Glysantin G 05
-80
-70
-60
-50
-40
-30
-20
-10
0
0 5 10 15 20 25 30 35 40 45 50 55 60
Concentration, volume %
Freezing Point, acc. ASTM D 1177
Frost Protection
Pour Point, acc. DIN 51 583
Foaming characteristics ASTM D 1881 max. 50 ml / 3 s
Swelling of rubber at 80°C/168 h 0 – 3 % for the SBR and EPDM qualities
50 % volume normally encountered on the
in water market, i. e. the same order of
magnitude as that for pure water.
Corrosion Performance
Glassware Corrosion Test ASTM D 1384
typical
Metals and alloys weight loss spec. limit
(mg/coupon) (mg/coupon)
Copper 0.0 10
Solder – 0.3 *) 30
Brass 0.6 10
Steel – 0.3 *) 10
Cast iron 0.6 10
Aluminium – 2.4 *) 30
Heat Transfer Corrosion Test ASTM D 4340
typical
weight loss spec. limit
(mg/cm²/week) (mg/cm²/week)
Aluminium – 0.9 *) 1.0
Simulated Service Test ASTM D 2570
typical
Metals and alloys weight loss spec. limit
(mg/coupon) (mg/coupon)
Copper 2.1 20
Solder 1.9 60
Brass 1.2 20
Steel – 1.0 *) 20
Cast iron – 1.1 *) 20
Aluminium 1.8 60
*) remark: negative values mean increase of weight.
Aluminum Water Pump Test ASTM D 2809
Test Period test result spec. limit
ASTM D 3306
100 hours 9 8
ASTM cavitation corrosion rating:
10 – perfect 1 – perforated
3
Quality control The above data represent average values at the time of going to press of
this data sheet. They can not be regarded as specified data. Specified
product data are issued as a separate product specification.
Storage stability Glysantin G 05 has a shelf life of at least three years when stored in
originally closed, air-tight containers at temperatures of maximum 30 °C.
Do not use galvanized containers for storage because they may corrode.
Safety Data Sheet A Safety Data Sheet conforming to EC-Directive 91/155/EEC is available
for Glysantin G 05.
Handling The usual precautions for handling chemicals together with the information
and advice contained in our Safety Data Sheet should be observed for
Glysantin G 05.
Avoid contact with skin.
Compatibility with other coolants Most coolant blends are based on carefully balanced mixtures of various
corrosion inhibitors. Mixing of coolants with different inhibitor packages can
lead to loss of corrosion protection. Glysantin G 05 should therefore not be
mixed with silicate free, OAT engine coolants.
Note The information submitted in this publication is based on our current
knowledge and experience. In view of the many factors that may affect
processing and application, these data do not relieve processors of the
responsibility of carrying out their own tests and experiments; neither do
they imply any legally binding assurance of certain properties or of suitability
for a specific purpose. It is the responsibility of those to whom we
supply our products to ensure that any proprietary rights and existing laws
and legislation are observed.
